Singer 14U64A Manuel d'utilisateur

14U64AOperator’sGuide

(3) Thread the left needle thread in the order ® to ® (blue mark).Threading of needle eye ® becomes easier when the movable knife is set at the non

m How to change threadsWhen you wish to change the left needle thread, right needle thread, left looper thread or right looper thread with

S & * &Adjust thread tension to suit the type of material and si2e of the thread used. The thread tension dials on this machine are

2) Standard 1-needle, 3-thread overedge stitchingThis machine can do I -needle. 3-thread overedge stitching by using only the right needle.Always remo

6. Hcv7 to Eojost Stitch lengthThe stitch length dial on this machine is pre-set to 3mm for normal sewing condition. Since the adjustm

This machine can do the 2 types of standard and ri^nt looper thread wrapped rolled hem stitching with a seam width of 13mm.Always remove the left need

3. How to adjust thread tension1. Standard rolled hem stitchingAs adjustments are the same as 1-needle, 3-thread overedge stitching, refer to page 1

• The minimum overedge stitch width that can be obtain* ed for relied hemming is approximately 1.5mm since the cutting width cannot be set below 3.5m

w «For ornamental and blind (overedge) stitching, use of the edge guide attachment is very convenient.Attach edge guide as shown in figure.12. Vcrist

4. Open iooper cover.5. Turn hand wheel toward you to bring movable knife to its lowest position and place it in the nonoperating position as shown

14Ü64APREFACEThank you for your purchase of this sewing machine-This machine will provide you with excellent performance in sewing from light to heavy

3-Thread blindstitchingBlindstitching provides a durable hem finish that is almost invisible* It is best suited for sewing cuffs on knitwear and ski

• 3*Thread pin tuckingPin tucking is a useful decoration when sewing blouses and children’s clothes. Pin tucking is accomplished before cutting out g

• Turning square cornersOutside comerCuttingline2cm2 cmNWcJ'L Cut out approxiniately 2cm from the comer in line with the overedge seam edge.2. S

13. r-cv;t3 rsp^£C3 r.ssd^ssUse Singer needles Cat. No. 2045 avaiiable in sizes #I 1 and #14.To remove the needles:® Be sure the power line plug is d

16, to £¿7^31 crasser foot pressiThe presser foot pressure of this machine i$ preadjusted at the factory to suit the sewing of medium w

18, Reasons for poor stitches ar.o hc*A* tc ntaks Ezyss’lrr.entWhenever sewing difficulty is encountered, make the adjustments as noted below.Conditio

» MW '*• ''’**1^ -H » W* » ♦ »ifi s^oth, thrSiType of Fabric Type of ThreadMeedleSinger Cat, No. 2045Light Weight Lawn, Organdy, Voil

(accessory box)Needle Set1.4^2.Screwdriver (medium size)13.Screwdriver (small size)14.Tweezers 15.Thread unwinder spool cap46.Stationary knifeI7.Brush

Form U3616 (Rev. 386)P an No. 379017*002 (Rev, 2) Printed in Japan

CONTENTSPage1. Principal parts...

S * ii S « >1^ S i?>*^ C« * i"** •» '«• ’ft*»Thread guide holderLeft hand iooper thread tension dial

2"^ ^ ^ -0«% ^ ^ «''i. ^ *'''«* iW, 'f ~"a *. ^ 'x*^ d - Cci- y», '<«*/ „ ^ «» vs y. s,

Thread the :::cGh:::8Setting up the thread guide holderExtend the thread guide holder as far as possible and set the thread guides so that they

# How to open looper coverBe sure rooper cover is ciossd when sewing.• How to remove cylinder coveras0 Push the cover to the ri^ht far as it will go a

• How to thread your machine correctlyCorrect sewing cannot be obtained when machine is threaded incorrectly.Threading is diagrammed on the inner

(2) Thread left looper in sequence from @ to 0 (marked in yellow color). Cylinder cover must also be removed when threading this part. (Refer to page